Exfo CableSHARK P3 VF/DSL Cable Qualifier Uživatelský manuál Strana 86
- Strana / 321
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
VF / DSL Cable Qualifier
74
8.1.2 Running a Frequency Response Test
Once the test is set up, press the RUN/STOP key located on the front panel of the CableSHARK. A screen
similar to Figure 8.1.2A will appear. The layout of the screen shows a graphic and numeric representation of
the information received by the CableSHARK. The graph’s vertical scale depicts the relative Attenuation
Level or Insertion Loss (in dB) and the horizontal scale depicts frequency (kHz). The distance to the found
valid reflection is shown on the status line.
Note: For the Single-Ended FR test, the CableSHARK can only measure the returned reflection
signals with up to 75 dB of attenuation.
The Cursor Position (kHz) and Attenuation (dB) are numeric representations of the solid cursor line bisecting
the result line of the test. By using the Cursor Pad LEFT/RIGHT arrow keys on the front panel of the
CableSHARK, the user can move the cursor line to different positions along the result line to see the
different values of frequency samples.
MAIN
MENU
EF
CHG
Single end frequency response test complete. (for 3995 ft)
dB
0.0
20.0
40.0
60.0
80.0
dB
Attenuation = 38.10 dB
Cursor Position = 1263.56 kHz
4 555 1106 22081657
SAVE/
UPLOAD
SHOW
REF
TEST
SETUP
0.0
20.0
40.0
60.0
80.0
ZOOM IN
HORIZ
kHz
Press or to move cursor
ZOOM IN
VERT
Figure 8.1.2A - Running a Frequency Response Test
Once the test has been completed, the status bar may indicate that the test was completed and/or to what
distance it was tested to or that no reflection was detected. At the completion of a test, the function button
- CableSHARK P3 3
- VF / DSL Cable Qualifier 10
- Patent Information 11
- 1.2 Unpacking the CableSHARK 13
- 1000 ft (300 m) 22
- 4.1.1 The Front Panel 27
- 4.1.2 The Rear Panel 29
- 4.2 Powering the CableSHARK 33
- 5.1.1 Self Tests 37
- 5.2.2 Single-Ended Testing 39
- 5.2.3 End-to-End Testing 40
- 5.3.1 Saving Results 41
- 5.3.2 Recalling Results 43
- 5.4 Reference Masks 45
- 5.6 Bandwidth Requirements 50
- Section 6 Main Menu 51
- 6.2 Responder Mode 58
- 6.3 Recall Results 59
- 6.4 The System Setup Menu 59
- 7.2.1 Automatic TDR Test 65
- 7.2.2 Manual TDR Test 66
- 7.3 Frequency Response Tests 67
- 7.4.2 End-to-End DMT Test 69
- 7.5 Noise Tests 70
- 7.7 Load Coil Detection Test 71
- 7.8 Spectral Detective 72
- 7.10 Return Loss 73
- 7.12 4 Wire Xtalk 73
- 7.14 ADSL Auto Test 74
- 7.15 SHDSL Auto Test 75
- 7.16 VF Auto Test 76
- 7.17 Ground Resistance Test 77
- 7.19 K-Test 78
- 7.20 Ringer Detection 79
- 7.21 VF Tests 79
- 7.22 LoopMapper™ Tests 79
- CableSHARK 81
- FREQUENCY RESPONSE TEST SETUP 84
- 8.2.1 Setting up a TDR Test 89
- 8.2.2 Manual TDR Testing 95
- 8.2.3 Auto TDR Testing 101
- 8.2.4 TDR Application Hints 102
- CableSHARK P3 User Guide 103
- 8.3.1 Setting up a DMT Test 105
- DMT BITS PER 107
- (m/μS): 108
- 8.3.2 Running an ADSL Test 110
- DMT TEST RESULT 114
- 8.4..Noise Measurements 118
- 8.4.2 Running a Noise Test 124
- 00:00:00 125
- TO MEM 130
- TO USB 135
- 8.7.1 Setting up a DMM Test 142
- 8.7.2 Running a DMM Test 148
- 8.8.. 4-Wire Crosstalk Test 151
- 17.3 kHz to 2.208 MHz) 155
- > 100 M 157
- 8.10 LoopMapper™ 159
- 8.10.2 LoopMapper Testing 161
- 8.11.1 Auto Test Setup 168
- IGURE 8.11.1.3C – PHONE BOOK 174
- Central Office 185
- Customer 185
- IGURE 9.2D – ADSL AT CO SIDE 191
- 11.1..Running a SHDSL Test 199
- IGURE 12.1C – BATTERY CROSS 201
- IGURE 12.1.1.3A – RFL CABLE 203
- Black Red Green 204
- Yel low Blue Green 204
- Black Red Gnd 208
- 12.2 Running a RFL Test 210
- 12.3 RFL Hints 212
- + [ 0.0022 * ( T 213
- - 68°F ) * R 213
- - 20°C ) * 0.00393 * R 214
- Line card = not detected 222
- 15.1.3 Sending 3 Tone Slope 233
- 15.2.3 RX 3 Tone Slope 240
- 15.3 Noise Test 243
- 15.4 Impulse Noise Test 245
- 00:09:12 246
- 15.5 Power Influence 247
- SAVE/UPLOAD button 248
- 16.2 Setting up a K-test 249
- 16.3 Running the K-test 250
- 16.3.3 Running a Test 256
- A.1 Loop Topologies 259
- A.2 Attenuation Responses 261
- Transmitter Characteristics 272
- Transmitter Functions 272
- ± 50 ppm 275
- ± 1.0 dB typical 275
- ± 0.5 dB 277
- SHDSL Data Rate Test 278
- PSD Noise Measurement 278
- Longitudinal Balance Test 279
- DMM (Digital Multimeter) 279
- Isolation resistance 280
- Spectral Detective 280
- 4-Wire Crosstalk 280
- Visi-SHARK 282
- Appendix D Safety 283
- Appendix E Warranty 287
- Certification 288
- F.1 Software Policy 289
- F.2 Upgrading Software 289
- J.1 Installing the Software 295
- J.3.1 Running Visi-SHARK 296
- IGURE J.4.2B – SOCKET ERROR 301
- J.6.1 File Menu 305
- J.6.2 Screen Image menu 307
- J.6.3 New Connection Menu 310
- J.6.4 View Menu 311
- J.6.5 Window Menu 311
- Telecom Test and Measurement 321
Související produkty a manuály pro Měřící nástroje Exfo CableSHARK P3 VF/DSL Cable Qualifier
Měřící nástroje Exfo DC0091A Uživatelský manuál
(3 stránky)
(3 stránky)
Měřící nástroje Exfo EPM-ELS-50 Uživatelský manuál
(206 stránky)
(206 stránky)
Měřící nástroje Exfo ETS-1000 Uživatelský manuál
(173 stránky)
(173 stránky)
Měřící nástroje Exfo ETS-1000G Uživatelský manuál
(195 stránky)
(195 stránky)
Měřící nástroje Exfo ETS-1000L Uživatelský manuál
(47 stránky)
(47 stránky)
Měřící nástroje Exfo FIP-400 Fiber Inspection Probe and ConnectorMax Uživatelský manuál
(78 stránky)
(78 stránky)
(2 stránky)
Měřící nástroje Exfo FIP-400B Fiber Inspection Probe and ConnectorMax2 Uživatelský manuál
(111 stránky)
(111 stránky)
Měřící nástroje Exfo FIP-400B Fiber Inspection Probe and ConnectorMax2 Uživatelský manuál
(103 stránky)
(103 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce